Barnes International, Inc. Kleenall Chip Filter Systems

Three RDXC-020 Kleenall Chip Filter Systems being inspected before moving to final assembly area.  Filters are arranged with magnetic bottoms and inclines for cast iron machining.  A 200 mesh filter belt assures fine particle removal.

The filters will be shipped to a large machine tool distributor for installation on machines and eventual shipment to customers.

For help with your filtration needs please visit www.barnesintl.com or call us direct at 815-964-8661.

Barnes MCS-620 Magnetic Separator

Inspecting Barnes MCS-620 Magnetic Separators before moving to the final assembly area where they will be fitted with tanks, pumps and controls before painting and shipping to customers.

The MCS-610 and MCS-620 magnetic separators are very popular in the industry because of their low cost, efficiency and ease of installation.

These units have flow rate capacities of 20 and 40 GPM respectively.  Normally in stock, they are usually available for immediate delivery.

Check our website at barnesintl.com to see our complete line of magnetic separators including BarMag and PlateMag.  Flow rate capacities up to 5,000 GPM are available.

Barnes International, Inc. Kleenall Max Filter

Front view showing chip.sludge discharge into conveniently located hoppers.

Rear view showing PLC controls and fabric rewinding mechanism.

Barnes International, Inc. of Rockford, IL, USA, a major builder of high quality filtration systems, has developed the Kleenall Max Coolant Filtration System to meet the needs of major automotive manufacturers worldwide. Over thirty units have been supplied to service engine and transmission machinery modules with flow rates varying from 2,000 L/M to 12,000 L/M (500 to 3,000 GPM).

Systems consist of a rotating drum (RD), permanent media filter precleaner to remove solids down to 30 microns nominal, a sidestream vacuum media polishing filter for 10 micron cleaning, and an automatic backflushing sentinel filter to provide full flow protection to all machines. 

The units are totally assembled and run off at our facility. They are built on skids with containment pans to contain any coolant spillage and require no special foundation, pits, or drain trenches. Single point connections for utility drops minimize installation time and cost. All equipment is robustly designed and maintenance friendly to give years of trouble free service. They ship mostly assembled with only a few parts to be bolted on at the job site.

Barnes International, Inc. is an innovative leader in the development of quality designed filtration systems. No system is too large or too complex for Barnes engineers to tackle. 

 

Visit us at www.barnesintl.com to see how Barnes products can solve your filtration problems. 

Barnes International – serving the needs of industry for over 105 years.

Barnes International Standard Products - A Review - Kleenall Filter

The Barnes MPE-10 Kleenall Magnetic and Fabric Filter

Combining a magnetic drum with a filter fabric second stage allows the Barnes system to remove finer particles in addition to non-magnetic materials such as abrasive wheel breakdown.  Like the magnetic separator line they are competitively priced and easily installed.

The MPE Series is undoubtedly the most successful filter of its type ever offered to the industry.  It has been widely copied the world over, but nothing comes close to the design features offered by this filter.

The MPE system can handle flow rates up to approximately 100 GPM.  Again these flow rates are based on water soluble coolants.

The PE Series is identical to the MPE Series with the exception of the magnetic drum which is not used.  Intended applications are grinding non-ferrous metals such as aluminum, brass and some alloy's.

For further information please visit www.barnesintl.com for more information.

President of Barnes International, Inc, William Kirchner congratulates our blogger and resident filtration expert Terry Connell on 55 years of service with our Company and still going strong!

Barnes International Standard Products - A Review

Historically, the Barnes product line - Magnetic Separators and Fabric Filters - have been recommended and used on grinding and finishing machines such as honing and some lapping machines.  The first of these is the standard Barnes Magnetic Separator.

The MCS magnetic separator line ranges in flow rate capacities from 20 GPM to 250 GPM with water based coolants.  First introduced during WWII, our magnetic separators offer low cost and low floor space requirements, along with ease of installation.  Although limited to ferrous applications they offer a lot of filtration for the money and provide a quick return on investment.

Information on more of our products to follow.

For additional information please visit us at http://www.barnesintl.com